How to choose a good quality car paint room and post-maintenance knowledge?

How to choose a good quality car paint room and post-maintenance knowledge?

At present, the national spray paint room market can be described as a mixed bag, with a wide range of brands, uneven quality and different prices. Many companies and maintenance owners have certain misunderstandings when purchasing: one is the lack of a comprehensive understanding of the brands in the market, the other is that they do not understand the professional knowledge of buying paint booths; the third is that they believe in propaganda, ignoring the effect of price and value. The fourth rule is to blindly pursue "cheap" and ignore long-term benefits. These circumstances are likely to bring irreparable economic losses to buyers. Therefore, it is recommended that users should pay attention to at least the following four points when purchasing a spray paint booth:

1. Focus on brand selection

    For any well-known brand, it must have excellent product quality and excellent service system as a guarantee, and ultimately be recognized by customers. Buying spray booths is the same as choosing other products, focusing on quality. Although there are about 400 paint booth manufacturers in the country, well-known brands such as Yancheng "Zhongda" and Guangzhou "Weilongda" have professional R&D, design, and manufacturing capabilities, with an annual output of over 1,000 units, and a sales network throughout the country. Yes, no more than seven or eight at most. Although the purchase of spray paint rooms depends on the investment and financial resources, it is still necessary to choose the best brands in the selection of high, medium and low-end products. The same configuration and quality are at a reasonable price. It is much more, the general price ranges from more than 20,000 to more than 40,000, and it is facing the mid-range economic consumption and investment. Therefore, it does not refer to the price and publicity of the luxury paint room.

    2. Pay attention to technical parameters

    Nowadays, many companies and maintenance owners who buy paint booths are very concerned about the price and ignore the technical parameters. This is a manifestation of the lack of professional knowledge about the purchase of paint spray booths. Such as the internal and external dimensions of the room, the air volume (m2/h), the load wind speed (m/s), the number of air changes (times/h), the highest working temperature, the heating time, the illuminance (Lux), the noise (dB), the TSP value (mg/m2), fuel consumption (kg/vehicle times), total power (kw), exhaust gas treatment methods and power requirements, etc. If the value of the technical parameters of the paint booth is unreasonable, it will definitely affect the use effect and increase energy consumption.

    3. Focus on price value

    People often say "there is no wrong sale, only the wrong one." The ultra-low price spray paint booths are shoddy in terms of materials and accessories, and it is not uncommon to use fakes. The standard spray paint booths are generally equipped with a room system, Eight systems including floor system, air supply and exhaust system, air purification system, heating system, environmental protection system, lighting system, electric control system, etc., are assembled with nearly one hundred processes and more than a thousand parts. Generally speaking, the price of the spray paint booth with the same configuration is more than 20% lower than that of the price. It must be "hands and feet" in one or more links. The lower the price of this kind of paint booth, the worse the quality and performance. The shorter the service life.

    Once the paint room is less than 30,000 yuan, there is no guarantee on the quality. The industry knows what the reason is, so when buying a paint room, don't buy it with the same price as it looks like the configuration. Often after investment, after-sales cannot be found within two years, no manufacturers can be found, enough to buy a paint room or choose a large-scale enterprise is more assured, mainly quality and after-sales. The reason why some manufacturers can't lower their prices is because they want to make brands, to ensure quality and after-sales. If speculative reductions reduce prices, after-sales must be troublesome manufacturers, or small workshops can't even find their addresses.

Maintenance of the paint room

   As a piece of equipment with a relatively large investment in the maintenance station, the roasting barn is not installed all at once. We have also seen that many of the roasting rooms at the repair station "strike" after only two or three years of use due to improper operation and untimely maintenance, and then have to spend a lot of money to repair it, which is a waste of money and affects the repair station. The development of normal work. The roasting barn needs daily correct operation and maintenance. In fact, it needs "seven-point use and three-part nourishment" just like a car. As long as you use it carefully and take care of it, the barn will surely grow longer with a small investment of money and less energy. Time is working in perfect condition, we will give a brief introduction to the maintenance of the roasting barn:

 

    (1) After a period of time, it is necessary to remove the dirt and residual paint residue in the air duct and the fan. They will not only cause the reduction of the fan power and the unsmooth airflow, but also cause the fire in the barn under extreme conditions. In recent years, there have been many barn fires caused by high temperature caused dirt and residual paint residue to catch fire.

    (2) After a period of time, the sealing condition of each part of the roasting barn must be checked. If there is leakage, it needs to be sealed in time to avoid affecting the sealing performance of the roasting barn.

    (3) Regularly replace the inlet cotton, top cotton and floor cotton.

   As a piece of equipment with a relatively large investment in the maintenance station, the roasting barn is not installed all at once. We have also seen that many of the roasting rooms at the repair station "strike" after only two or three years of use due to improper operation and untimely maintenance, and then have to spend a lot of money to repair it, which is a waste of money and affects the repair station. The development of normal work. The roasting barn needs daily correct operation and maintenance. In fact, it needs "seven-point use and three-part nourishment" just like a car. As long as you use it carefully and take care of it, the barn will surely grow longer with a small investment of money and less energy. Working in perfect condition of time.

   Development direction of paint room technology

    With the development of the market and the continuous application and popularization of cutting-edge scientific research results, the technical requirements of the paint baking room have attracted more and more attention and concern from customers. In terms of technological changes, mainly from these aspects:

1. Environmental protection requirements. As people continue to understand and improve environmental protection requirements, environmental protection has increasingly become a prerequisite for customers' choices.

2. The heating mode provided by the paint baking room has been diversified. The baking barn is not limited to a single heating mode, there will be two or three four heating modes coexisting to reflect, so as to improve the efficiency of the paint bake room.

 

3. In terms of energy supply mode. Due to the shortage of natural energy and the high price, a single energy supply and method for curing barn energy can no longer be the demand of market development. With technological improvement, multiple energy supply methods coexist, such as natural gas and liquefied gas. Other clean and fast energy sources will become the development trend.

Fourth, in terms of plate design, various panels will be more concentrated in the application of single-chip microcomputers. The single-chip microcomputer will show its skills in the monitoring, adjustment, and safety processing of the paint booth, and the control and application of the baking room will be broader and more comprehensive.